Handling noise and clothing rustle in recordings
Checked against the product on October 22, 2026
Handling noise is the thump or scrape heard when a microphone is touched, and rustle is the sound of fabric rubbing against a lavalier. Prevent both by mounting the microphone on a stand, taping the cable, placing a lavalier on stable cloth away from jewellery and scarves, avoiding gestures near it and testing with headphones. Record the line again if damage is severe.
What you are seeing
Sudden knocks, a scratching sound with each movement or a rhythmic rubbing beneath the voice. The noise may be small on speakers but clear on headphones, and captions can stumble exactly where it occurs.
How to fix it
- Mount the microphone on a standNot held in the hand.
- Tape or clip the cableNo tugging.
- Clip a lavalier to stable clothAway from collars and scarves.
- Use a small loop of cableRelieves strain.
- Remove jewellery and noisy itemsNecklaces, watches.
- Avoid gestures near the microphoneOr talk with still hands.
- Test with headphonesWalk, sit, turn.
- Record the damaged line againA calm retake is best.
Common causes
- A handheld microphone or phone.
- A lavalier rubbing against a collar or scarf.
- Cable pulled by movement.
- Jewellery touching the clip.
- Knocking the desk or stand.
What to avoid
Do not apply strong software repair that muffles the voice, and do not tape a microphone directly to bare skin or delicate fabric. Avoid placing a lavalier where chin movement brushes it.
In Averoai.pro
Averoai.pro transcribes the speech in your video, so rustle and thumps can cause missed words. A clean recording gives better captions, and a short re-recorded line can replace a damaged moment.
A worked example
A trainer's lavalier rubbed a scarf and produced a scratch with each nod. Moving the clip to the jacket lapel and placing the scarf behind the shoulder removed the sound, and the captions needed far fewer corrections.
Worth remembering
Noise from touch is a mechanical problem with a mechanical fix. Stabilise the microphone, secure the cable and test with headphones. Keep a small kit of clips, tape and a spare lavalier in your bag, and make walking and turning around part of your pre-recording test, so that surprises appear before the recording rather than after. If you record the same set-up regularly, take a photo of the final microphone position and cable route, because a well-placed microphone is easy to disturb when you adjust the camera or move a chair, and a photo lets you restore the arrangement in a few seconds before the next session begins.
Frequently asked questions
What is handling noise?
The sound of touching or moving the microphone.
Where should a lavalier sit?
On stable cloth, away from collars and scarves.
Can software remove it?
Only partly.
Does it affect captions?
Yes, it can cause missed words.
Features that help with this
Related reading
- A clip whose intro or logo animation is too long
A long intro delays the point and loses viewers in the first seconds. Learn how to cut or rebuild intros and logo animations so the clip starts on its message.
- A video file that is too large to upload
Big files fail to upload or take forever. Learn how to check the limit, trim the length, lower the bitrate or use a link instead of a file.
- Wind noise in outdoor recordings
Wind rumble drowns speech and ruins captions. Learn how to shield the microphone, change position and record again so outdoor clips stay clear.
- A constant hum or buzz in a recording
A steady hum or buzz under speech tires listeners and hurts captions. Learn how to find the source, record again if needed and clean what you can safely.
- What is variable frame rate?
Variable frame rate changes the number of frames per second as a recording runs. Learn why it can drift out of sync and how to convert it to constant.
- What is reverb in a recording?
Reverb is the wash of reflections that follows a sound in a room. Learn why hard, empty rooms sound boomy and what simple steps make speech clearer.
Also available in Français