What is a pop filter?
Checked against the product on October 22, 2026
A pop filter is a thin screen placed between a speaker and a microphone to soften plosives, the bursts of air on sounds like p and b that cause a thump in a recording. Angling the microphone slightly off-axis and keeping a little distance also help. Fewer thumps mean a clearer voice and easier listening on small speakers.
Definition
When you say 'push' or 'big', air leaves your mouth quickly. A close microphone registers that burst as a low thump. The pop filter, made of fine mesh or foam, slows and spreads the air so that the microphone hears the voice rather than the wind.
Ways to reduce plosives
| Method | How it helps | Note |
|---|---|---|
| Pop filter | Spreads the burst of air | Place a hand's width from the microphone |
| Off-axis angle | Air misses the capsule | Aim slightly beside the mouth |
| Distance | The burst weakens | Too far adds room sound |
| Foam cover | Absorbs some air | May dull the sound slightly |
| Editing | Filters low thump | Cannot fix every case |
Setting up
- Place the filter between mouth and microphoneClose to the microphone.
- Leave a gapDo not touch the mesh with your lips.
- Angle the microphone slightlyNot straight at the mouth.
- Say a test phraseTry 'Peter picked a big bag'.
- Listen on headphonesCheck for thumps.
- Adjust distanceUntil the voice is clear and steady.
Where it matters
- Voice-overs and narration.
- Podcasts and talks recorded with a close microphone.
- Videos watched on phones and earbuds.
- Any recording where bass thumps are distracting.
Not needed everywhere
A lavalier worn on the chest or a microphone at arm's length rarely suffers from plosives. The problem belongs mostly to close, front-facing microphones.
How Averoai.pro relates
Averoai.pro transcribes the speech you provide. Heavy plosives can distort a word and cause a caption error, so a clean voice recording makes captions more accurate. Fixing the sound itself belongs to your recording setup or audio software.
A worked example
A narrator found that every 'p' thumped on phone speakers. Adding a pop filter and angling the microphone slightly to the side removed the problem, and the captions of those words became correct.
Worth remembering
A pop filter is cheap and quick to set up, and it protects a recording from a very noticeable flaw. Place it carefully, keep your distance consistent and listen back before the long session starts. A clean voice makes every later step easier.
Frequently asked questions
What is a plosive?
A burst of air on sounds like p and b that causes a thump.
Do I need a pop filter with a lavalier?
Rarely; the problem mostly affects close microphones.
Can editing remove plosives?
It can reduce them but cannot fix everything.
How far should the filter be from the microphone?
About a hand's width.
Features that help with this
Related reading
- What are proxy files in video editing?
Proxy files are lightweight copies of large videos used to edit smoothly. Learn what they are, when they help and how they differ from the original footage.
- Organic reach versus paid promotion
Organic reach comes from people finding or following you; paid promotion comes from payment. Learn the difference, labels and cautions for creators.
- What is a decibel?
Decibels measure how loud a sound is, and in editing they show your levels. Learn what the numbers mean and which ranges suit speech clips.
- What is room tone?
Room tone is the quiet background sound of a space. Learn why recording it helps edits sound smooth and how it relates to noise, echo and clear captions.
- What is a lavalier microphone?
A lavalier is a small clip-on microphone placed near the mouth. See where it shines, where it struggles and how it improves captions and clips.
- What is audio ducking?
Audio ducking lowers background music automatically while someone speaks and raises it again in pauses. Learn how it works, when to use it and common settings.
Also available in Français